2

Diamond Abrasion: Definition, Causes, Grading and Buyer Checks

# A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Diamond Abrasion is a surface blemish consisting of tiny nicks along polished facet junctions or the culet. Under magnification, affected edges may look white, fuzzy, or frosted instead of crisp. Its importance depends on location, severity, visibility, polish condition, and whether similar abrasion appears repeatedly across a wholesale parcel.

Diamond abrasion refers to tiny nicks along facet junctions of a polished diamond, or sometimes, around the culet. When viewed under magnification, affected edges appear fuzzy or frosted. Abrasion is usually caused by some aspect of the cutting, handling, or storage process. It may also be caused by repeated contact with other diamonds. The importance of diamond abrasion depends on the amount, the location, how visible it is, and how it affects the evaluation of the finish and clarity of the diamond.

What Is Diamond Abrasion?

Abrasion is the presence of nicks along diamond facet junctions. Nicks along facet junctions give diamond edges a fuzzy or white appearance. The International Organization for Standardization (ISO) diamond grading terminology describes diamond abrasion as tiny nicks along facet junctions or the culet edge that replaces a sharp edge with a fuzzy edge. Abrasion is considered a surface flaw, rather than an internal inclusion. A lightly abraded junction may not be visible without magnification. A heavily abraded junction appears frosted.

When evaluating the quality of a diamond, it is important to consider abrasion. The presence of abrasion, the amount of abrasion, and the location of abrasion are important when assessing a diamond’s quality and finish.

What Does Diamond Abrasion Look Like?

Diamond Abrasion usually occurs along facet junctions rather than forming a single line going through the center of a facet. With the right type of controlled lighting and enough magnification, you may lose the crisp edge and see a group of small, whitish marks along the edge. When a lot of small abrasions happen together, the edge may appear frosted or fuzzy.

Knowledge of diamond facets helps to recognize the feature since abrasion will also follow the same boundaries. Abrasion may occur along crown or pavilion junctions, along the girdle or around the culet, depending on how the stone has been handled or worn.

Abrasion may be hard to recognize, and a diamond may still appear attractive face-up. Abrasion can be seen at 10x magnification along a small area of the stone. Abrasion becomes a bigger issue if it occurs over a wider area, making the diamond appear to lose its crisp finish.

What Causes Diamond Abrasion?

Hardness does not guarantee that a polished gemstone will not show surface wear. GIA separates durability of a gemstone into hardness, toughness and stability. Hardness refers to the resistance of a gemstone to abrasion and scratches. Toughness refers to resistance of a gemstone to breaking and chipping. GIA notes that the hardness of diamond may also vary with crystal direction.

Some of the reasons diamond abrasion may occur include:

  • Contact with other diamonds: During transportation or storage of diamonds in the rough or polished state, they may rub against each other. If there is a hard surface or edge on a diamond, it may abrade another diamond.
  • Cutting and Polishing: Surface damage can occur from improper manufacturing, like repetitive contact with hard materials or other stones. The American Gem Society says one type of surface damage, abrasion, can occur during the cutting process and from improper handling. This can result in small nicks or pits along facet junctions.
  • Parcel Storage: Movement within parcels, jars, trays or sorting containers can cause unnecessary contact between polished stones.
  • Jewelry Wear: Prolonged contact with hard surfaces can affect exposed junctions.
  • Repair and Service: Diamonds can be exposed to unnecessary contact during repair, cleaning or handling, if insufficient protection is provided.

It is important to know the difference between abrasion and scratching. Abrasion describes a fuzzy edge, whereas scratching is a sharp edge. Likewise, nicks and chips are also important to distinguish from abrasion.

Nick

Usually a discrete area of minor damage.

Chip

A more substantial damaged area that has the potential to affect the contour of the stone.

A diamond scratch is characterized as a very thin, fine mark, and abrasion as a series of nicks along an edge. The International Organization for Standardization defines a scratch as a linear, or slightly curved, indentation, which is commonly seen as a fine, white line.

A Diamond Chip is usually more substantial and may affect the outline of a stone. A nick is usually more localized and is much less substantial.

This is important in the quality control process because not every white line should be identified as an scratch. An isolated nick, for example, should not be mistaken as a scratch.

How Diamond Abrasion Relates to Polish

Diamond polish is the smoothness of facet edges and surfaces. Therefore, the quality of facet junctions is relevant to the finish of a diamond.

Abrasion does not always mean that the entire diamond suffers from poor polish. A small localized feature may not have a big visual impact, and may be less significant, while a number of larger localized features across multiple junctions may be more significant.

The American Gem Society states that assessment of polish includes consideration of facet edges and surfaces, and that abrasion is a finish fault that is evident along junctions of facets.

Buyers of certified diamonds need to evaluate complete grading information, not simply rely on a single surface characteristic. Information such as the type of polish, clarity, measurement and plotted characteristics (when provided), and the current physical condition of the diamond, need to be analyzed in combination.

Can Diamond Abrasion Affect Clarity?

Yes. Diamond abrasion can have an effect on clarity, and GIA classifies abrasion as an example of a blemish. The impact of abrasion is not the same for all stones. For example, a few tiny abrasions may have very little importance, whereas larger and more visible abrasions may have a greater importance. Location of abrasion is also relevant. Abrasion along a prominent facet junction may be more noticeable than abrasion in a location that is not prominent and is difficult to be detected under magnification.

When considering wholesale quality of a diamond, abrasion should be considered in conjunction of other external and internal characteristics. The intent is to understand if the total condition is aligned with the represented quality and the commercial requirement.

Can Diamond Abrasion Be Polished Out?

In a case where a diamond abrasion is not too deep and not too large, it can be polished away. In such a case, professional re-polishing of a diamond can restore a more cleaned-up, and thus improved, condition of the diamond. When thinking about re-polishing of a diamond, proportions need to be evaluated to determine if polishing would have an adverse effect on the overall condition of the diamond.

A minor scratch would not normally warrant additional cutting. More apparent scratching may require further examination before the stone is sold, set, recertified, or included in a quality controlled parcel.

How to Inspect Diamond Abrasion

Uniform processes help correct for common reflections, polish marks, scratches and dust that can mimic abrasion.

1. Clean the Diamond First

Oil, polish, dust, and finger prints create a haze that can mask stone junctions. Before assuming that a stone junction is abraded, make sure the stone is free of residues by using proper cleaning procedures.

2. Use Controlled Magnification

Standard gemological magnification, 10x, is adequate for inspection.

3. Follow the Facet Junction

If the line is frosted, it is abraded. If a line is frosted and extends independently across a facet, it is most likely a scratch.

4. Check the Girdle and Culet

Because these are exposed edges, they should be examined closely as well.

5. Compare With Stone’s Grading Info

A copy of the grading report will indicate the polish and clarity characteristics as well as comments by the grader. Other considerations may include how the stone was set and handled after it was graded.

6. Inspect More Than One Stone in a Parcel

Depending on the context, repeated parcel-wide features and isolated surface characteristics of individual stones may suggest different scenarios for B2B sourcing.

For example, a cluster of stones with abraded edges may indicate a sorting or transport issue rather than individual stones being handled in isolation.

Why Diamond Abrasion Matters in B2B Quality Control

When considering whole parcel analysis, “abnormal” conditions including Diamond Abrasion (e.g. an abrasion line, or chipping) may be within an accepted quality range. However, repeated Diamond Abrasion may indicate an unacceptable handling or finishing problem.

Buyers should assess the following:

  • Is abrasion evident on a single stone or across the parcel?
  • Is the condition evident to the naked eye or only with the help of a loupe?
  • Is the polish consistent with the specification?
  • Would polishing stones to restore the condition cause loss in weight or production?
  • Would the stones meet the quality parameters specified by the supplier?

Lepdo Diamonds is located in Surat, India. As a B2B supplier, stones are evaluated for surface conditions (e.g. abraded edges, nicks, scratches, etc.) along with other parameters (e.g. shape, size, finish, uniformity, certification, and clarity) prior to being processed for use in jewelry.

Buyers may wish to read about durability of lab grown diamonds here.

How to Prevent Diamond Abrasion

Diamond-to-diamond contact should be avoided as much as possible.

Keep polished diamonds separated while handling and storing them if possible. Use tools and equipment to keep diamonds separate. Minimize shaking and movement of diamonds. During the repair or setting of jewelry, protect exposed diamonds from contact with hard tools and loose stones.

Abrasion should be avoided after final polishing since additional unneeded damage may occur and increase the work needed to finish the stone. Proper handling may prevent more damaging nicks and scratches.

Abrasion Occurs When a Diamond Comes in Contact With Another Diamond

Abrasion occurs when a diamond comes in contact with another diamond. The contact causes a tiny nick along the junction. Over time the nick may spread and deepen, or it may even manifest along other facets.

Diamond Abrasion vs. Diamond Scratching

Abrasion and a scratch are different. A nick occurs along the junction and is usually not defined like a scratch.

Not Every Abrasion Needs to be Repolished

Not all abrasions require a diamond to be re-polished. The decision is made based on the location and extent of the abrasion, the finish requirements, the purpose of the stone, and its value.

Abrasion of Diamonds Is Always a Manufacturing Defect?

No, it can happen during service and usage of the diamond as well. If an abrasion is present without other known issues, it cannot be assumed that the abrasion occurred during the last polishing stage.

Abrasion Automatically Makes a Diamond Unsuitable

Minor localized abrasion may be of no practical concern. If, however, abrasion is of sufficient intensity and/or distribution, the stone warrants further technical and commercial consideration.

Frequently Asked Questions About Diamond Abrasion

1. Is Diamond Abrasion an Inclusion?

Diamond Abrasion is considered a blemish since it occurs on the surface of the diamond. An Diamond Inclusions is something that happens internally and extends into the body of the diamond.

2. In what areas of the diamond is abrasion commonly seen?

Abrasion is most often associated with facet junctions and is sometimes seen at the culet. Under magnification, a facet junction loses its edge and appears to be fuzzy and frosted.

3. Can Diamond Abrasion lower a diamond’s grade?

Diamond abrasion can affect a diamond’s grading if it is large enough and can be seen with the unaided eye. If the abrasion is small and obscured by the reflectivity of a facet, it may not lower the grade of the diamond.

4. Can diamonds abrade each other?

Yes. Rubbing a diamond against another diamond can abrade a facet junction.

5. Can abrasion be seen without magnification?

Minor abrasion may not be seen without the aid of a magnifying glass. More extensive abrasion may be seen without a magnifying glass, especially if there are several facets that have lost their edges and appear fuzzy.

6. Can abrasion be repaired?

Re-polishing may help reduce surface abrasion. Location, depth, potential carat weight loss, and finish should all be considered to determine if correcting the feature adds a sufficient commercial or visual benefit.

7. Should buyers automatically reject stones with abrasion?

No. In considering abrasion, buyers should evaluate finish and grading standards, parcel uniformity, intended end use, and the size and location of abrasion.

A repeated condition across a parcel should deserve more attention than a single, small, isolated occurrence.

8. What is the difference between abrasion and a rough girdle?

Abrasion is minor nicking of the facet junctions or culet. A rough Diamond Girdle describes an irregular or granular girdle. They are two completely different external features of the stone.

Practical Takeaways for Buyers

Diamond Abrasion should be viewed more as a surface condition issue which reduces the crispness of facet junctions. It should be determined whether the condition is severe before a quality or commercial decision is made.

For buyers, jewelers and sourcing teams, the best course is to review the stone under a microscope and judge how abrasion compares to the polish and clarity of neighboring stones.

WhatsApp